Santa Ana, CA · Licensed & Insured · 2-Year Warranty
Fiberglass Bathtub Enclosure Reglazing in Santa Ana, CA
One-piece fiberglass and acrylic tub and shower units restored from the floor up. We repair cracks and soft, flexing floors, then reglaze the entire enclosure into a smooth, glossy, like-new surface in a single day. Licensed, insured, 2-year written warranty.
- 10+ Yearsof experience
- 2-Year Warrantyon every service*
- Licensed & InsuredCalifornia contractor
- Same-Dayappointments available
- Free Estimateswritten, no obligation
*Kitchen sinks carry a 6-month warranty because of the heavier daily wear they take.
Fiberglass & Acrylic Units
The bathtub you cannot replace without tearing out the wall
Most fiberglass enclosures were installed before the drywall went up. They are larger than the bathroom door, so a replacement means cutting the old unit into pieces, opening the walls, and either framing in a multi-piece surround or rebuilding with tile. For a Santa Ana condo or apartment that is a $6,000 to $10,000 project and a week without a bathroom.
Reglazing the enclosure is the sensible alternative, and it is the job we do most for property managers and landlords across Santa Ana. We handle the structural problems first, because a coating over a flexing floor will crack, and then recoat every surface of the unit, tub floor to ceiling line, as one seamless shell.
- Crack repair with fiberglass reinforcement, not just filler
- Soft floor repair with injected structural foam
- Yellowed, chalky gelcoat restored to bright gloss
- Built-in soap dishes, ledges and seats coated as part of the unit
- Anti-slip tub floor and fresh silicone on every job
Symptoms
Signs your fiberglass enclosure needs reglazing
Floor flexes or creaks
Lack of support under the tub. Left alone, it cracks. We foam-fill the base so it feels solid as cast iron.
Spider cracks or a split in the floor
Stress cracks are ground out, reinforced and sealed. This is a repair, not a patch over the problem.
Yellow, dull, chalky surface
Oxidized gelcoat. Reglazing replaces it with a thicker, UV-stable finish.
Stains that will not clean
Once gelcoat is porous it absorbs dirt and hair dye. The new coating is non-porous.
Peeling DIY paint or kit
We strip failed coatings completely before starting over the right way.
Unit is rent-ready except for the bathroom
Landlords: one day, one invoice, no demolition, tenant moves in on schedule.
Our Process
How we restore a fiberglass enclosure
Fiberglass units need structural work before cosmetic work. Here is the order we do it in.
- 01
Full structural check
We press-test the floor, probe for soft spots, check every corner and seam for cracks and inspect the drain area.
- 02
Structural repair first
Soft floors are foam-filled. Cracks are ground out, reinforced with fiberglass mat and resin, then filled and sanded flush.
- 03
Strip, degrease and sand
Old silicone, soap scum and oxidized gelcoat are removed. The entire unit is sanded for adhesion.
- 04
Bonding primer
A primer formulated for fiberglass and acrylic chemically bonds the new coating to the old gelcoat.
- 05
Spray topcoat
Multiple coats of acrylic urethane over tub, walls, soap dishes and ledges for a single seamless finish. Anti-slip texture on the floor.
- 06
Recaulk and cure
Fresh silicone where the unit meets the wall and floor. Ready for use in 48 hours with your written 2-year warranty.
Our Warranty
Backed in writing for 2 full years
Every reglazing service we perform in Santa Ana is backed by a written 2-year warranty on workmanship and finish. If the coating peels, bubbles or fails because of our prep or application, we come back and make it right at no cost. The only exception is kitchen sinks, which carry a 6-month warranty because of the heavier daily wear they take from pots, pans and dishes.
- Written warranty handed to you on the day of service
- Covers peeling, bubbling, cracking and loss of adhesion caused by our work
- Simple care instructions so the finish lasts well beyond the warranty
Service Area
Fiberglass enclosure reglazing across every Santa Ana neighborhood
We are based in Santa Ana and drive to you. Most appointments inside the city are scheduled within a few days, and same-day service is often possible for single fixtures. We regularly work in these neighborhoods and ZIP codes:
Santa Ana neighborhoods
Santa Ana ZIP codes
92701, 92703, 92704, 92705, 92706, 92707
Nearby cities
FAQ
Fiberglass enclosure questions from Santa Ana owners
Still have a question? Call (714) 439-5614 or request a free quote and we will answer it directly.
A one-piece or multi-piece molded unit that combines the bathtub and the shower walls, usually fiberglass with a gelcoat surface or acrylic. They were installed by the thousands in Santa Ana apartments, condos and tract homes from the 1970s onward because they are cheap and quick to install. They are also nearly impossible to replace without tearing out the bathroom wall, which is why reglazing is the standard fix.
Yes. Cracks in fiberglass tub floors are usually caused by flexing over an unsupported base. We repair the crack with fiberglass reinforcement and, where the floor is soft, inject structural foam underneath to stop the flexing before reglazing. This is a permanent repair, not a cosmetic patch.
Yes. A soft or spongy floor means the unit was installed without proper support underneath. We drill small access holes, fill the void with expanding structural foam, patch the holes and then reglaze the whole unit. The floor comes out solid.
A full tub and surround unit is typically 5 to 7 hours. Add an hour or two if there is structural floor repair. The unit is ready for use after 48 hours.
The factory gelcoat is thin and breaks down with UV light, hot water and cleaning chemicals. Once it goes, the surface is porous, stains easily and feels rough. Our acrylic urethane coating is thicker and more chemical-resistant than the original gelcoat.
No. Done properly, the finish is sprayed in multiple thin coats and levels out to a smooth, high-gloss surface that looks like a new molded unit. The difference between our work and a painted-on kit is preparation, materials and equipment.
More Services
Other reglazing services in Santa Ana
Bathtub ReglazingPorcelain, cast iron, fiberglass and acrylic tubs restored to a factory-gloss finish in one day.Learn more
Sink ReglazingBathroom and kitchen sinks refinished in place. No plumbing work, no countertop damage.Learn more
Shower ReglazingTile showers, pans, cultured marble and fiberglass stalls sealed and reglazed as one watertight surface.Learn more
Tile Wall & Floor ReglazingDated ceramic tile walls and floors recolored and sealed without demolition.Learn more Get your fiberglass enclosure restored this week
Send a couple of photos, including any cracks, and we will send a written quote within one business day.
Mon–Fri 8am–6pm · Sat 9am–4pm · Sun closed